Centrifuge:
-Manual Top Discharge
-Bag Lifting
-Bottom Discharge
From 12" Dia. up to 60" Dia.
Top Discharge
The manual Top Discharge Centrifuge is a basic model where the filtered cake is manually scooped out. This is the most commonly used.
Sizes:
From 12″ Dia. up to 60″ Dia.
Materials of Construction : SS-316L, SS-304, CS and Hastelloy .
Coating: Halar (ECTFE), Teflon (PFA), Rubber Lining.
- Safety device such as zero speed lock for the centrifuge cover
- Vibration limiter
- RPM sensor with indicator
- Pneumatic lid opening system
- Hydraulic lid or body opening systems
- Gas tight centrifuge design
- Nitrogen purging/blanketing with PLC control.
- Cleaning in place (CIP)
- Cake thickness sensor
- 4-point suspension -Centrifuge is mounted on four viscous dampers
- Variable frequency drive: the operating speeds of the centrifuge are controlled by a variable frequency drive. The standard braking system for this model is dynamic braking
- Taper lock pulleys: these pulleys are easier to mount and dismount
- Cake washing nozzles: special spray nozzles with defined conical pattern spray are provided so that the entire surface of the cake is covered uniformly with minimal quantity while maintaining repeatable washing performance
- Shaft protection sleeve: a stainless steel sleeve is mounted on the exposed part of the shaft to protect it from corrosion
- Proximity sensor: to prevent the machine from being started while the lid is open a proximity sensor is installed
- Gas tight design: the machine is constructed to retain a positive pressure of 400mm water column
- Easy maintenance: the machine design affords minimal maintenance. Greasing points enable easy lubrication of the bearings
Model No. | UNIT | MTP 24TD | MTP 36TD | MTP48TD | MTP 60 TD |
Basket diameter | mm. | 610 | 915 | 1220 | 1524 |
Basket Depth | mm. | 300 | 450 | 450 | 500 |
Working cap under lip | ltrs. | 50 | 160 | 260 | 450 |
Basket load(max) | Kgs. | 63 | 200 | 325 | 563 |
Max. Basket Revolutions | Rpm. | 1400 | 1100 | 900 | 850 |
Centrifugal Force | G. | 657 | 609 | 540 | 609 |
Filtration Area | m2 | 0.59 | 1.29 | 2.049 | 2.39 |
Motor Power | Kw. | 2.2 | 5.5 | 11 | 15 |
OVER ALL DIMENSION OF MACHINE | |||||
Length over motor (L) | mm. | 1450 | 1780 | 2150 | 2500 |
Width(W) | mm. | 1000 | 1220 | 1600 | 2000 |
Operation Height | mm. | 1175 | 1350 | 1650 | 2100 |
Weight of Machine with motor | Kgs. | 1150 | 2750 | 4000 | 5500 |
Bag Lifting Type
From 24" Dia. Up To 60" Dia.
In this model the filter bag is fastened to the basket top plate. The basket top plate is in turn locked onto the basket shell. When the filtration is completed, the plate is removed by unlocking the plate from the basket shell and pulled out using a hoisting arrangement. The filter bag containing the product comes out of the centrifuge. The product is then moved out to a suitable location and unloaded. The main advantage of this machine is that the unloading time is reduced considerably and also has less manual intervention when compared with a manual top discharge centrifuge. High production rates can be achieved with this machine.
Materials of Construction : SS-316L, SS-304, CS and Hastelloy.
Coating: Halar (ECTFE), Teflon (PFA), Rubber Lining.
- Safety device such as zero speed lock for the centrifuge cover
- Vibration limiter
- RPM sensor with indicator
- Pneumatic lid opening system
- Hydraulic lid or body opening systems
- Gas tight centrifuge design
- Nitrogen purging / blanketing with control system
- Cleaning in place (CIP)
- Cake thickness sensor
- 4-point suspension -Centrifuge is mounted on four viscous dampers
- Variable frequency drive: the operating speeds of the centrifuge are controlled by a variable frequency drive. The standard braking system for this model is dynamic braking
- Taper lock pulleys: these pulleys are easier to mount and dismount
- Cake washing nozzles: special spray nozzles with defined conical pattern spray are provided so that the entire surface of the cake is covered uniformly with minimal quantity while maintaining repeatable washing performance
- Shaft protection sleeve -a stainless steel sleeve is mounted on the exposed part of the shaft to protect it from corrosion
- Proximity sensor: to prevent the machine from being started while the lid is open a proximity sensor is installed
- Gas tight design: the machine is constructed to retain a positive pressure of 400mm water column
- Easy maintenance: the machine design affords minimal maintenance. Greasing points enable easy lubrication of the bearings
MODEL NO. | UNIT | MTP 24 BL | MTP 36 BL | MTP 48 BL | MTP 60 BL |
Basket diameter | mm. | 600 | 900 | 1200 | 1500 |
Basket Depth | mm. | 300 | 450 | 600 | 600 |
Working Cap. Under Lip | Ltrs. | 65 | 205 | 300 | 590 |
Basket load(max) | Kgs. | 81 | 256 | 375 | 737.5 |
Max. basket revolution | Rpm. | 1400 | 1100 | 900 | 850 |
Centrifugal force | G. | 657 | 609 | 540 | 609 |
Filtration area | M2 | 0.58 | 1.29 | 2.26 | 2.82 |
Motor Power | Kw. | 2.2 | 5.5 | 11 | 18.5 |
OVERALL DIAMENSION OF MACHINE | |||||
Length over motor (L) | mm. | 1450 | 1780 | 2150 | 2500 |
Width(W) | mm. | 1000 | 1220 | 1600 | 2000 |
Operation Height | mm. | 1800 | 2400 | 2900 | 3200 |
Weight of Machine with motor | Kgs. | 1350 | 3000 | 4750 | 8000 |
Bottom Discharge
From 36" Dia. Up To 60" Dia.
Bottom discharge centrifuge’s provide rapid acceleration, low current consumption and powerful efficient braking. The bottom discharge centrifuge basket has radial ribs instead of a flat bottom plate. The gaps in the basket bottom facilitate the cake discharge on to the inertia plate and to the bottom hopper.
The inertia plate too has radial ribs and large openings that allow the discharged cake to fall into a hopper fitted below the inertia plate. The monitor casing is fitted with a scrapping arrangement (also known as plow) on which a knife is mounted in such a way that the cake inside the basket is peeled-off when the knife is engaged.
Materials of Construction : SS-316L, SS-304, CS, Hastelloy & Titanium.
Coating: Halar (Ectfe), Teflon (PFA), Rubber Lining.
- Zero speed interlock
- Charge regulator
- Vibration monitoring system
- Nitrogen purging/Blanketing control system
- Vibration tripper
- Easy and quick cake discharge
- Less manual labour involved
- Cake handling loss negligible
- Easy scraping of cake through scraper
- Handling of discharge solids can be easily done with the help of a conveyor or trolley
- No manual contact with cake, thus no contamination
- Solids can be discharged in totally vapour tight condition, thus no health hazards and environment is clean. Solids discharge through single outlet
- Good accessibility to the casing and basket makes quick cleaning and changeover to other products easy
- The centrifuge is driven by variable speed AC inverter drive/Eddy current coupling, the rotational speed of the basket can be set to match the filtration properties of the suspension
- Discharge of solids take place at lower basket speed (around 80 RPM) thus making possible particularly gentle handing of the product. In this way, the undesirable breakage of crystals is nearly eliminated
- Spray jets for efficient washing
- Nitrogen blanketing for centrifuge, body and bearing housing. The complete centrifuge is pressure tested as per DIN standard
- 4 point suspension -Centrifuge is mounted on four viscous dampers
- Variable frequency drive: The operating speeds of the centrifuge are controlled by a variable frequency drive. The standard braking system for this model is dynamic braking.
- Cake washing nozzles: Special spray nozzles with defined conical pattern spray are provided so that the entire surface of the cake is covered uniformly with minimal quantity while maintaining repeatable washing performance
- Taper lock pulleys: These pulleys are easier to mount and dismount
- Shaft protection sleeve: A stainless steel sleeve is mounted on the exposed part of the shaft to protect it from corrosion
- Proximity sensor: To prevent the machine from being started while the lid is open a proximity sensor is installed Gas tight design: The machine is constructed to retain a positive pressure of 400mm water column
- Easy maintenance: The machine design affords minimal maintenance. Greasing points enable easy lubrication of the bearings
MODEL NO. | UNIT | MTP 36 | MTP 36 D | MTP 48 | MTP 48 D | MTP 60 | MTP 60 D |
Basket diameter | mm. | 915 | 915 | 1220 | 1220 | 1524 | 1524 |
Basket Depth | mm. | 450 | 600 | 500 | 650 | 500 | 750 |
Working Cap. Under Lip | Ltrs. | 160 | 220 | 300 | 400 | 500 | 750 |
Basket load(max) | Kgs. | 200 | 275 | 375 | 500 | 625 | 930 |
Max. basket revolution | Rpm. | 1100 | 1100 | 900 | 900 | 850 | 850 |
Centrifugal force | G. | 609 | 609 | 540 | 540 | 609 | 609 |
Filtration area | M2 | 1.29 | 1.72 | 1.91 | 2.49 | 2.39 | 3.59 |
Motor Power | Kw. | 7.5 | 7.5 | 15 | 18.5 | 18.5 | 22.0 |
OVERALL DIMENSION OF MACHINE | |||||||
Length over motor | mm. | 1780 | 1780 | 2150 | 2150 | 2500 | 2500 |
Operation height | mm. | 1500 | 1700 | 2325 | 2500 | 2250 | 2500 |
Weight of machine with motor | Kgs. | 3000 | 3100 | 4500 | 4750 | 7000 | 7500 |